Ridder Tubemotor System
The Ridder RB50Eᵖˡᵘˢ tubular motor is a maintenance-free drive unit for driving roll-up screen systems in greenhouses and livestock houses. The tube motor is integrated as standard into a 50 mm aluminium tube (wall thickness 1.5 mm) and can be used with 50 mm roll tubes. Because it is integrated, the tube motor can be wound up completely.
The almost-silent RB50Eᵖˡᵘˢ tube motor is fitted with a 1-phase 2-core asynchronous electric motor, an integrated brake and permanently lubricated planetary gear unit. The tube motor has a self-repairing thermal protection system, which prevents the burn-out of the drive if the electric motor should overheat.
The RB50Eᵖˡᵘˢ tube motor is almost entirely water resistant. The high protection class, IP55, means that the function of the tube motor will not be affected by a damp atmosphere.
The RB50Eᵖˡᵘˢ tube motor has as standard an intelligent and precision pulse-counting electronic limit-switch system with a range of 38 revolutions. This pulse-counter switches off the tube motor when it reaches its end position and also switches it off for safety reasons in the case of an overload. The switch components in the new electronic limit-switch system allow several tube motors to be connected in parallel without using an isolating relay.
Installing the RB50Eᵖˡᵘˢ tube motor is quite simple. In combination with the Ridder guiding unit and guide rail, the tube motor can be fitted in a roller screen system, both right and left.
- Drive torque of 50 Nm at 50 Hz
- Revolutions of 3.5 rpm at 50 Hz
- Suitable for intermittent use, operating class s3-6%, duty cycle (kb) 10 minutes
- Supplied in accordance with protection class IP55
- Reliable motor brake behaviour, also when operating with undervoltage
Ridder RB50E+ tubular motor 1-phase 2-core asynchronous electric motor IP55. Range of 38 rev. - Suitable for 50mm Tube
4.2kg 230v 1 Phase 0.56 Amps 50hz 50x1.5mm Tube
$1,232.99
Please call or Use the enquiry form below and advise us of your needs, and we can make the recommendations to suit your individual application.
Please send us an enquiry to [email protected] or use the button below.
Tubemotor Accessories
The RMC50 motor control units are control boxes used to connect the 1-phase RB50/ RB50Eᵖˡᵘˢ tube motors. In the RMC50 motor contol unit, all the electric components needed to ensure the safe operation and the safe connection and drive for a RB tube motor.
$493.88
Zinc-plated bracket for mounting the cable carrier to the RB50Eᵖˡᵘˢ tube motor. The bracket should be mounted on the tube-motor head between the tube motor and the guiding unit.
$10.13
Zinc-plated mounting bracket used with the cable carrier end connection (female) for tube motors
$10.13
The cable carrier guides and protects the power cable of the tube motor. The cable carrier is hinged in one direction and rigid in other directions . The power cable can be fed in easily. Attach the cable carrier to the tube motor using the mounting kit.
$31.70
Zinc-plated guiding unit used to conduct the RB40/50-RB50Eᵖˡᵘˢ tube motors in the guide rail. Capable of absorbing the torque and axial forces of the tube motor. The tube motor is fitted to the guiding unit with a square shaft pin (10x10 mm) and secured with a split pin.
$108.08
Mounting kit for attaching the cable carrier to the guiding unit or the cable carrier bracket for the RB50Eᵖˡᵘˢ and RB120Eᵖˡᵘˢ tube motors for use in greenhouse structures. Mounting kit consists of two end clips for the cable carrier, 4 pop-rivets and 3 cable ties.
$18.45
Adjusting switch for the RB50Eᵖˡᵘˢ and RB120Eᵖˡᵘˢ tube motors for 1-phase, 230 V/50 Hz should be used when setting up the RB50/120Eᵖˡᵘˢ tube motor. The end position of the tube motor can be set up, changed or re-set using the adjusting switch. The adjusting switch has a plastic connector with pressure clamps (for connecting the RB50/120Eᵖˡᵘˢ tube motor), a switch unit with push buttons and a rim-earth plug.
$83.25
For use with guiding units for the RB50Eᵖˡᵘˢ/120Eᵖˡᵘˢ, RB40/50 and RB120 tube motors. Guide rails can be supplied with a zinc-plated mounting bracket. Supplied in 4000mm lengths.
$150.41
Wall Ventilation Accessories
25NB Galvanized Steel Pipe (33.3OD) 2.6mm wall thickness x 3250mm long with 75mm Swagged one end
* Discount on 10+ Lengths*
$45.82
38mm x 25m Per Roll. Used to secure roll up walls when no external screening is used, or in extremely windy conditions.
Can be used in a X pattern in windy locations.
38mm x 25m Per Roll.
$38.23
